Automatic DB 5801 Instrukcja Użytkownika Pobierz pdf (Strona 2)

Shots to Lockout

The selectable shots-to-lockout feature prevents the

source-side protective device from reclosing into a fault

multiple times.

Loss of Phase

6801 Controls protect three-phase loads from single-phas-

ing by automatically opening the switch. The controls can

be programmed to automatically reclose the switch when

three-phase voltage returns.

Hot Line Tag

Hot Line Tag can be set with either a SCADA command or

with a configurable button on the faceplate. It can only be

cleared by the command type used to set it.

Switching Devices Supported

6801 Series Controls support the following switching

devices:

• S&C Scada-Mate® Switches

• S&C Scada-Mate CX™ Switches

• Other specific switching devices listed on page 3.

For applicability to other switching devices, refer to

your nearest S&C Sales Office.

EXCLUSIONS: 6801 Automatic Switch Controls do not

include a communication device, antenna, or antenna

connections.

For non-IntelliTeam SG applications, S&C may be able

to furnish and install in the 6801 Automatic Switch Control,

or make provision for, a customer-specified communica-

tion device not listed in the table on pages 5 and 6. S&C will

need to evaluate the physical and electrical requirements

of the communication device and its performance charac-

teristics, and conduct qualification testing to verify its suit-

ability for the desired application. Refer to the nearest S&C

Sales Office for scheduling information. S&C cannot fur-

nish or install any communication device for which the

supplier requires S&C to offer Tier I (i.e., “help desk”)

support.

SPECIFICATION DEVIATIONS: Refer to the “Options”

table on pages 5 through 7.

SPECIAL WARRANTY PROVISIONS: The standard

warranty contained in seller’s standard conditions of sale,

as set forth in Price Sheet 150, applies to S&C 6801 Auto-

matic Switch Controls, except that the first paragraph of

said warranty is replaced by the following:

(1) General: Seller warrants to the immediate purchaser

or end user for a period of 10 years from the date of

shipment that the equipment delivered will be of the

kind and quality specified in the contract description

and will be free of defects of workmanship and mate-

rial. Should any failure to conform to this warranty

appear under proper and normal use within ten years

after the date of shipment the seller agrees, upon

prompt notification thereof and confirmation that

the equipment has been stored, installed, operated,

inspected, and maintained in accordance with recom-

mendations of the seller and standard industry prac-

tice, to correct the nonconformity either by repairing

any damaged or defective parts of the equipment or

(at seller’s option) by shipment of necessary replace-

ment parts. The seller’s warranty does not apply to

any equipment that has been disassembled, repaired,

or altered by anyone other than the seller. This limited

warranty is granted only to the immediate purchaser

or, if the equipment is purchased by a third party for

installation in third-party equipment, the end user of

the equipment. The seller’s duty to perform under any

warranty may be delayed, at the seller’s sole option,

until the seller has been paid in full for all goods pur-

chased by the immediate purchaser. No such delay

shall extend the warranty period.

Replacement parts provided by seller or repairs per-

formed by seller under the warranty for the original

equipment will be covered by the above special war-

ranty provision for its duration. Replacement parts

purchased separately will be covered by the above

special warranty provision.

WARRANTY QUALIFICATIONS: Warranty of S&C 6801

Automatic Switch Controls is contingent upon the installa-

tion, configuration, and use of the control or software in

accordance with S&C’s applicable instruction sheets. This

warranty does not apply to major components not of S&C

manufacture, such as batteries, communication devices,

and remote terminal units. However, S&C will assign to

immediate purchaser or end user all manufacturers’ war-

ranties that apply to such major components.

END USER LICENSE AGREEMENT: End user is

granted a nontransferable, non-sublicensable, nonexclu-

sive license to use the LinkStart Connection Management

Software, IntelliLink® Remote Setup Software, Intel-

liTeam® Automatic Restoration Software, Automatic Sec-

tionalizing Software, and/or other Software furnished with

6801 Automatic Switch Controls only upon acceptance of

all the terms and conditions of the seller’s end user license

agreement set forth in Price Sheet 155.

How to Order

Select the catalog number of the desired 6801 Automatic

Switch Control from the table on page 3.

1. Add the suffix for the type of switching device from

the table on page3.

2. Add the suffix for the control software type from the

table on page3.

3. Add the suffix for the mounting type from the table

on page4.

4. Add the suffix(s) for any options desired from the

table on pages 5 through 7.

5. Add the suffix(s) for gateway applications, if required,

from the table on pages 8 and 9.

S&C 6801 Automatic Switch Controls

2 S&C Specication Bulletin 1045-31

1 2 3 4 5 6 7 ... 10 11

Komentarze do niniejszej Instrukcji

Brak uwag

Automatic DB 5801 Instrukcja Użytkownika Strona 2

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Elektronarzędzia Automatic DB 5801