Automatic COBRA Instrukcja Instalacji

Page 1Cobra®Overhead Garage Door OpenerInstallation Manual

Page 10INSTALLATION (continued)'UDZ 9HUWLFDO &HQWUH /LQHIURP 'RRU WR +HDGHU+HDGHU'RRU)LJ STEP TWO:Determine the centre of the doo

Page 11INSTALLATION (continued)STEP SIX:Lay the rail on the ground with channel side facing up. Insert the Traveller and Chain Idler assembly into the

Page 12INSTALLATION (continued)STEP EIGHT:Locate chain at Drive unit end onto drive unit sprocket. Keeping chain taut on sprocket, insert drive unit c

Page 13INSTALLATION (continued)STEP ELEVEN:Determine a suitable method to support the drive unit from the ceiling depending of the direction of ceilin

Page 14INSTALLATION (continued)STEP THIRTEEN:Place the drive unit on the garage fl oor with corrugated cardboard or old carpet underneath to prevent da

Page 15INSTALLATION (continued)STEP FIFTEEN:Ensure door is fully closed. Pull traveller and straight arm by hand until straight arm can be attached to

Page 16INSTALLATION (continued)STEP SEVENTEEN:Pull door to half-open position until chain spool engages inside traveller. Plug in power to Drive Unit

Page 17PROGRAMMING - Door Travel LimitsSETTING DOOR TRAVEL LIMITSTo code transmitter for setting limits 1. Select Handheld Mode using the LEARN button

Page 18PROGRAMMING - Safety Force MarginPlease take care when testing the Safety Obstruction Force. Excessive force may cause DEATH, SERIOUS PERSONAL

Page 19CODING TRANSMITTERSPROGRAM A TRANSMITTER BUTTON TO OPERATE THE DOOR 1. Select Handheld Mode using the LEARN button on the unit. Display shows

Page 2

Page 20CODING TRANSMITTERS (continued)PROGRAM A TRANSMITTER TO ACTIVATE VACATION MODE 1. Select Vacation mode using the LEARN button on the unit. Di

Page 21ERASING TRANSMITTERS / FITTING PE BEAMSERASE TRANSMITTER FROM MEMORY 1. Select Erase mode using the LEARN button on the unit. Display shows (

Page 22AUTO-CLOSE / COURTESY LIGHT / PET MODESETTING THE AUTO-CLOSE TIME IMPORTANT NOTICE: IT IS COMPULSORY TO INSTALL A PHOTO ELECTRIC BEAM BEFORE US

Page 23RESTORE FACTORY SETTINGS / WIRING VACATION LOCKRESTORE FACTORY SETTINGS KEEP ALL TRANSMITTER CODES / RESET ALL OTHER SETTINGS1. Select Factory

Page 24WIRING ALARM/STATUS OUTPUT & EXTERNAL LIGHTSWIRING ALARM / STATUS OUTPUTPressing the transmitter button associated with the Alarm function,

Page 25FACTORY DEFAULT SETTINGS & SPECIFICATIONSDefault Step Value MaximumMotor Run Time 30 seconds - -Courtesy Light Time 3 minutes 10 seconds 10

Page 26

Page 27WARRANTY1 - This warranty is an addition to any non-excludable conditions or warranties that are implied into this contract by relevant statute

Page 28AUTOMATIC TECHNOLOGY AUSTRALIA PTY LTDABN 11 007 125 3686-8 Fiveways Boulevard, Keysborough, Victoria, 2173Tel: +61 3 9532 2788 Fax: +61 3 953

Page 3WARNING – IT IS VITAL FOR THE SAFETYOF PERSONS TO FOLLOW ALLINSTRUCTIONS. SAVE THESEINSTRUCTIONS!Watch the moving door and keep people awayuntil

Page 4Thank you!Welcome to the installation and instruction manual for your new Automatic Technology Cobra overhead garage door opener.Created and des

Page 5PRODUCT FEATURESOPERATION To open or close the door simply press the hand held transmitter, the wall mounted transmitter, or optional wall switc

Page 6OPERATING CONTROLS/($51 ,167$//.ALMLTLCK24VOSCCOMCOMPEP1P212345671. ENGAGE DISENGAGEMENT HANDLE, EASY ACCESS TRANSMITTER The “manual release” en

Page 7OPERATING CONTROLS4. DISPLAY General Display Codes dcc ro7 Flashes on the display once the opener powers up (dc opener chain drive, fi rmw

Page 8OPERATING CONTROLS (continued)6. TERMINAL P1 (continued)Light (LT)A 24V DC relay of the appropriate contact voltage can be connected to the ligh

Page 921INSTALLATIONTools you may need)LJ D7LOW GRRU IL[LQJ6HOIGULOOLQJILQH WKUHDGWHFVFUHZV'RRU EUDFNHWIOXVK ZLWK WRSRIGRRU'RRU EUDFNHW